Optimal...

The lockdown is showing obvious signs of recession, although outside of certain hours, the roads remain refreshingly silent. Another week, a further 150 miles drumming my shape into the Univega’s saddle, while enjoying the more willing persona and supple ride quality, provided by those aptly named Continental Speed Reflex tyres.  

I’d also set aside some time to dial in the shifting (which wasn’t quite so precise at the lower half the cassette), then craft some custom paint protection using the Zefal Frame Armor. Rubberised cable buffers have greatly reduced the dreaded cable rub and my fleet has very thick, powder-coated finishes.

  

However, grit and oily contaminant can get lodged between the frame and soft polymer cuff, gnawing away at the lacquer and colour coats, albeit at a comparatively pedestrian rate.  

Pre-cut sticker sets have been around for donkeys and the more expensive versions are not only thick but employ strong adhesives. The sort highly resistant to solvents, oils, UV light and frequent washing. High-quality workshop type rolls are the most cost-effective options. They also permit custom shapes. The trade-off being achieving this demands a methodical, unhurried approach.  

Whether you’re applying these, or pre-cut types, give the frameset a sudsy bucket wash, then designated areas a quick rub with an alcohol-based wipe. This will remove anything dirty oily/waxy that would otherwise impair adhesion. 

I’ve also applied a strip to the underside of my fixed gear winter/trainer’s downtube since opportunity presented. Placing a strip here is a good move, even on a mountain bike using a crud catcher style guard, since the zip ties securing them can slip/move gnawing into the frame finish, over time. Especially when wet, gritty mud’s thrown into the equation 

Staying with the fixed, I’ve switched to the 32mm Kenda Kwick Journey KS Plus-wholesale. Much roomier around the rear triangle (Not that 35mm was problematic, per se) and true to their moniker, noticeably livelier, than the otherwise likable and very dependable VEE Tire Co Zilent https://www.sevendaycyclist.com/vee-tire-co-zilent-mark-2-tyres.  

This also brings the gearing down a fraction, to 75.6 inches, which is also more manageable in less fluid traffic and when climbing.  The 5mm thick puncture repelling strip doesn’t run bead to bead, which hasn’t proved problematic thus far and may also account for the friskier persona.  

However, we’ve passed hedge clipping season and wet, slimy winter roads might reveal some vulnerabilities.      Those looking for a budget digital pressure gauge might find this Lifeline Digital Pressure gauge fits the bill https://www.sevendaycyclist.com/lifeline-digital-pressure-gauge 

32mm was once the preserve of traditional touring and off duty ‘cross bikes but allowing for the trend towards bigger sections (I’m more inclined toward a 700x38c for road-biased touring)  it still strikes a good balance between speed and comfort, especially given the UK’s patchwork infrastructure. Talking of which, I’ve just received this latest incarnation of the Cane Creek Thudbuster.  

Specifically, the Cane Creek Thudbuster ST G4. The latter denoting 4th generation. The Thudbuster ST https://www.sevendaycyclist.com/cane-creek-thudbuster-suspensuin-se had a phenomenally long run and still has a lot of merit, especially on older, higher-end cross country mountain bikes. Not least since it's available in more sizes, with shims to bridge the gaps.  

This time around, it's only available in 27.2 or 30.9 and 31.6mm. (There are also two lengths-345mm for 27.2 and 375mm for 30.9 and 31.6mm). However, they’ve updated the linkage design. Elastomers are more easily swapped around, and it theoretically caters for riders up to 350lb.  

I say theoretically since the saddle clamp is a single bolt affair. A moot pint for a 70 old kilo “whippet” but experience suggests riders teetering around the 110-kilo mark might notice some saddle-rail creep. In terms of travel, the G4 has 50mm. 17mm more than the long-serving ST and 15mm more than the Redshift Shock stop Suspension post, presently pride of place on my Holdsworth. I’ve had to forgo the Carradice Carradry SQR bag https://www.sevendaycyclist.com/carradice-carradry 

But thankfully, this Altura Aero Post Pack was doing something close to nothing and capacity aside, the powder-coated aluminium alloy frame keeps it away from the post, thus solving potential compatibility hassles. Of course, you could always go the rider mounted route, for commuting and light trail duties. Oxford Aqua Evo 12 Litre Backpack is a lightweight and genuinely waterproof option. https://www.sevendaycyclist.com/oxford-aqua-evo-12-litre-backpack 

New Guards & Big Flaps

Ended up stripping the Univega of the mighty Tortec chrome plastics, while I waited for these superbly solid SKS BLUEMELS SHINY 26″ 60 BLACK SET to arrive. Good thing I did too, since the front was one rattle away from falling atop the tyre, and launching me over the bars.

Sans guards it has a very rugged, raw simplicity. Arguably closest to the original 80's concept that fired my teenage imagination, its trail potential was fully realised, along with some seriously big grins for a few evenings. 

The first was quite cold, frosty, although rains returned the following two nights. Thankfully I've been testing these Funkier Aqua Water Repellent Tights. Very welcome (Competent too, especially considering the asking price (£74). 

Talking of the 80's, though frame fit pumps have largely disappeared (thanks in no small part to compact geometry framesets, and mountain biking's other influences) Zefal HPX High Pressure Frame Pump remains quite relevant. https://www.sevendaycyclist.com/zefal-hpx-frame-pump 

I returned from Tuesday night's mud spattered meander to find the SKS guards waiting. 

Not the sort of job I wanted to embark on, then. Wednesday morning came and I wasted no time in un-boxing and weighing the guards, which are 50g lighter than the Tortec. 

Next my beloved tubby tourer was popped in the workstand, stripped of wheels and given a rich, sudsy bucket wash. 

Rinsed and dried, I turned my attentions to the front guard. Fitting mudguards can prove fiddly, rather than difficult. In this instance, it's complicated by my preference- a Gusset Uni Head system, rather than the Star Frangled Nut (SFN). 

Now, these might carry a weight penalty over the humble SFN, or expandable wedge type systems. However, they offer improved security. I've never had one work loose and they're also reckoned to keep things together, in the event of a steerer crisis. One of many experiences I would like to keep academic. 

However, it does preclude attaching mudguards via the fork drilling. I judiciously cut out the riveted stainless steel mount, using a hot blade. Given the quality of chrome plastics, and valuing my own digits, this had to be done in three stages. 

Having established the uni-head's bottom nut would slide snugly through the hole, I began bolting the guards in situ. Measure twice cut once when tackling the stays but otherwise everything bolted together smoothly, sans faff.

Achieving graceful, flowing lines is very simple with this calibre of mudguard too. 90, rattle free miles in, and despite the absence of mudflaps coverage is surprisingly good. Nonetheless, presented with a scrap Panaracer tyre, I decided to cut and fashion a set. 

Arguably pop-riveting would've been the neatest method but I settled on a high-strength glue, left clamped and curing for 24 hours. Though not a precision cut, they're neat enough and I've been refining things, gently sanding excess glue-at least where it can be seen. Besides, blasted with dodgy looking water, diarrhoea like mud and other greasy midwinter muck, they'll blend in nicely!  

Talking of which, the Weldtite TF2 Performance all weather lubricant https://www.sevendaycyclist.com/weldtite-tf2-performance-all-weather has fared much better than the Juice Lube Ceramic Juice Chain Lube in comparable conditions. 

The Ceramic Juice hit 185 before the dreaded squeak struck but I should point out, its actually blended for dry to moist, rather than wet weather. 

Therefore, I will reserve judgement and resume testing once (some might say, if) we get a decent dry spell. Meantime, I've switched to their Viking Juice, which they say, is the most durable of their range. 

Application is reminiscent of early ceramic blends in the sense its applied in stages. Whereas some required you to ride around, before adding a final layer, Viking Juice takes but a few minutes. 

Between 2 and 4 coats are recommended, so having established we're in the depths of winter, I've gone the whole hog. 

Its a really runny formula too, designed to seep deep within the chain, so keep some clean rag handy and resist any urges to apply indoors. My Univega's drive train feels suitably frisky but staying prowess is another thing entirely. 

Been rather impressed by their JL69 Bike Maintenance Spray, which seems versatile, durable and very competitively priced. Cleat/mechanisms, locks, cables and jockey wheels have all cheered up with a squirt. Electroplated Allen bolts and similar fasteners have also remained taint free.  

Been rather impressed by this Naked Bikes Pro Wax Special Edition, too. https://www.sevendaycyclist.com/naked-bikes-pro-wax-special-edition  . Though hardly cheap, the quality and durability of finish is very impressive. A Christmas gift idea, for the rider who is tricky to buy for.