Showing posts with label Bobbin handlebar tape. Show all posts
Showing posts with label Bobbin handlebar tape. Show all posts

Thursday 27 April 2017

Polished Performer







A semi-sheared side plate put a temporary stop to last week’s back road blasting on the Holdsworth. Unusually for me, spare links were conspicuous by their absence. Thankfully said weakness was spotted at the end of Tuesdays’ outing, not ten miles from base. A generous helping pruned from the Ilpompino’s inox unit were later found in its wedge pack.



 
Rather like spare tubes and patch kits without a pump or CO2 inflator, links aren’t a fat lot of use without a suitable chain tool. Those found on some multi tools will do an excellent job of splicing and re-joining beefy track types. However, keep this infrequent. to avoid fatigue. Even if the pin doesn’t pop, the spreader slots can eventually crumble.

 
That said; I’ve been stunned to discover some pricey models marketed as “Workshop” used relatively soft aluminium drive pins, which inevitably expired within a month’s moderate use.  
 
A new KMC was sourced at a very favourable price. I’ve pruned a few links for spares but otherwise leaving it complete for a rainy day. I’ve also decided to whip the wheel round and use the 16tooth alloy 3/32 sprocket, delivering a marginally lower gear.  


 


Staying with chains a moment, here’s the mid-term (3 month) review of the Weldtite TF2 extreme wet, which had served my ‘cross inspired fixer’s chain from January onwards https://www.sevendaycyclist.com/weldtite-tf2-extreme-wet-chain-lubr

 


Weather is still quite changeable, erring on the wintry and for the meantime; I’m sticking with some middleweight formulas. Here’s a quick guide to lubes and the science behind them https://www.sevendaycyclist.com/blank-ao363
 
Before I’d discovered the fractured side plate, an audible click when under load pointed to the right hand Time ATAC XC4. Not the most obvious pedal choice for a road build, let alone TT bike. 


 
However, I much prefer dual sided models for quick getaways. These are resin bodied, which save a few grams. Plentiful float is good news for knees and there’s plenty of ground clearance too.
 
The only downside for me is their use of brass cleats, which, being a softer metal wear faster and are pricier to replace compared with SPD. Admittedly, price is partly due to a lack of patterns. SPD can be found pretty much anywhere and I’m yet to find some that aren’t universally interchangeable. 


Elsewhere the postman brought me some kit from Brian Davis I’ve been rather impressed by his concepts. First up, we have the fix-it sticks T way wrench http://fixitsticks.com/for-bikes , which is simplest described as the big brother in the range, designed specifically for workshop duties. The fixed T handle is made from high quality nickel plated, heat treated chrome vanadium steel.


Supplied with 7 contemporary bits 2, 2.5, 3, 4, 5, 6 and Torx, it’s also fully compatible with any standard ¼ bit, which is a refreshing change. These are held securely within the ends using neodymium magnets and there’s a handy pouch to keep everything in. No excuse for losing anything, unless the cat decides to sweep them from the workbench and to the least accessible point!

 
While my initial rummage through the spares drawer for off cuts of track chain might’ve seemed in vain, the arrival of some titanium polishes and the Univega’s recent post upgrade has stirred an unexpected revival.
The Ilpompino’s otherwise excellent perch has been substituted for this Brooks Colt pattern with titanium rails. A lick of nourishing food to the Australian cowhide and it coordinates beautifully with the equally pleasing Bobbin wrap https://www.sevendaycyclist.com/bobbin-leather-bar-tape.

 
This sits atop the super refined Thudbuster St for now…I’ve given the Ti bottle cage a quick polish, replaced the high volume Lezyne micro floor drive for its high pressure sibling. Right, that’s me done for now. Wonder how that clump of dried earth got lodged in its right hand issi pedal….


Friday 23 October 2015

Dollars, Discs & Distractions















 
I was contacted by someone via “Up work” inviting me to write for them this week.  Keeping an open mind, I responded asking for their exact specification-sign of the times perhaps but, these sites tend to foster a race-to-the-bottom mindset where remuneration’s concerned.
A few minutes later, I received a further email offering me $17 Canadian dollars for a 1,000 word feature including photographs! "Up yours" was a tempting retort but rather than dignify this with a response, I decided stripping and cleaning the Ilpompino’s disc setup was a more positive use of my energies.
Avid’s BB7 is a markedly easier system to adjust than their justly popular BB5 but mine had become misaligned, causing the inboard pad adjuster to brush the spokes. I hadn’t taken a spill, or incurred similar trauma but a thorough back to basics exorcism seemed the most remedy.
Removing the front wheel and inspecting the 160mm Shimano rotor confirmed it was perfectly true and snug aboard the hub. Next stage was to disconnect the cable and reseat the calliper. 5mm Allen and 25 torx keys at the ready, I slackened the mounting hardware; then wound the pad adjusters out, before driving then fully home against the disc rotor. Centring the calliper is simply a matter of pushing it against the fork mount and then tightening the mounting screws.
Strictly speaking, I should’ve reconnected the cable at this point but was following my own intuitive flow, centralising the pads and double checking everything by spinning the wheel. Cable reconnected, a very gentle whisper was corrected by a quick turn of the outboard pad. Spinning the wheel and engaging the Cane Creek lever ten times to verify (and/or placate my advancing neurosis); I repatriated tools and drizzled a little more lube on the chain. Unfortunately Writer’s block was still a sitting tenant, so my attentions turned to mowing lawns before they assumed jungle status and while October still permitted.
Down time paid off, since paragraphs and inspiration flowed consistently once I’d settled back at my middle aged desktop. Four days and 100miles hence verified everything’s behaving impeccably and while I’ve a thing for fierce brakes and solid lever action, allowing fractionally more cable slack has rewarded with more progressive stopping, though pulled in anger, there’s sufficient wallop to raise the rear several inches from the ground.
That Bobbin bar wrap continues to impress with its stylish, shock absorbing properties. Tenure bare handed, even in the wet is pretty impressive too; not that I ride without gloves with any regularity.
The G-Eye2 action is another pleasant surprise and a definite improvement on its predecessor. Whether it’s a poor man’s Go Pro, in much the same sense Triumph’s GT6 was to Jaguar’s E-Type remains to be seen, although it does illustrate how far budget tech has come along in recent years.
Recording quality is good and ideal for developing video reportage skills but the Go Pro will shoot professional grade footage, whereas the G-Eye 2 is firmly in enthusiast hobbyist territory. 
Despite daily rides of 20miles plus, sometimes the walls can start metaphorically closing in. Needing some inspirational escape, I headed out in the Micra with my trusty NEX5 and stopped off at Maldon Shot Blasting & Powder Coating.
Alongside various classic Porsche shells and a 1966 GT40 race car, the methyl chloride tank was making short work of this MG BGT’s blue 2pac paint, revealing plenty of filler and the original orange livery beneath.
This scabby but otherwise sound Specialized Rockhopper built from a Ritchey Nitanium steel alloy tubeset was also awaiting blast and pale blue powder coat makeover and certainly held my attention. I’ve always been a big fan of Specialized’s iconic steel Stump jumper and rock hopper series since first clapping eyes on them back in 1986/7. 
The romance of adventure, exploring foreign lands on a lightweight go-anywhere bicycle was an obvious draw. Then of course, the thrill of speeding along deserted singletrack, flicking around tree roots-just me, the machine and my thoughts-often fuelled by magazine contraband and rudely interrupted by a teacher’s confiscation!
Detailing suggests this one’s of 1998 vintage and while the cable run places them right in gloop’s path, I like the clean aesthetic and would be inclined to build it into a pared to the essentials 1x10 drop bar adventure bike with old school, wide arm cantilevers, fast rolling knobblies, 12-30 cassette...
Back to the future and speaking of romance, I’m due at a wedding, so will pack camera equipment into the Ka and head off to Bedfordshire.