Progress & Priorities

 

On some levels and to some extent, everything in life is a work in progress. That out of the way, I was still being taunted by the intermittent brake tickling and concluded everything was otherwise correctly aligned...Perhaps the outer housing from lever to first cable stop was fractionally too short... 

I'd had plenty of compression-less outer and had earmarked inner cable replacement, so an obvious thing to rule out and a simple fix. Something that came to mind during that meditative mid- ride phase.  

I've also been contemplating the rack and trailer compatibility conundrum.

One potential solution was to fit an adaptor that would raise the racks' legs, providing the necessary clearance without compromising the rack's payload. Now, I'm talking a high quality, properly machined stainless/6061 aluminium alloy, not the sort made from cheese. However, closer inspection of the Topeak’s “foot” revealed this a non-starter. Some folks recounted shaving metal from the foot with their trusty Dremel…Nope, not for me. Besides, braking was my primary focus-this needed to be right before we're tethering trailers.

The solution came courtesy of Madison cycles and a M Part Ridge rack. Weighing 624g, it's a single tier design loosely reminiscent of Blackburn's MTN. One that served me well until its demise while riding through Forest Gate (E7) late summer 1999. Credit to Blackburn, they honoured their lifetime warrantee and I received a replacement. The Ridge is made from 10mm 6061 aluminium rod, comes complete with a no quibble 5-year warrantee and a respectable 25kilo maximum payload.

Designed for disc brakes, it employs adjustable legs and oodles of calliper clearance without the "feet" which preclude trailer fitment. There's a solid top plate doubling as a mudguard for easy porting of rack bags and loose stuff captured by a cargo net. Stainless steel fasteners are another nice, corrosion-resistant touch. However, I found the arms too short for Ursula, preventing it sitting level, so switched them for the  Topeak's. 

Single tier models can make pairing of panniers and trunk bags less convenient than their two-tier counterparts and means weight is also positioned a little higher. All things being equal and in the everyday sense, I've never had any major issues lugging 20-litre panniers with Blackburn and homages.     

One of the most faithful homages to the Blackburn MTN was produced by Bor Yeuh. I bought one over thirty years ago for £15 and it was very much bombproof and surprisingly well-finished. There’s an argument for using threadlock on fasteners, rather than grease-especially ahead of a tour. In these contexts, I’ve always carried a few spare nuts and bolts, should one make a bid for freedom. However, I didn’t have any medium strength threadlock to hand, so added a coating of Zefal Pro ii Zefal Pro II Grease | cycling-not-racing, which should keep the elements out.

 These and other little fasteners are easily overlooked until you want to remove or adjust something. In a pinch, heavyweight wet lubes, or 10w/40 motor oil make passable grease substitutes, and I’ve found fasteners mobile a few months down the line. Nonetheless, for daily drivers and other mile munchers, re-greasing every six months or so remains best practice.  If in doubt, apply a quick squirt of MO94 Muc-Off MO94 Multi Use Spray | cycling-not-racing, GT85 GT85 ALL PURPOSE LUBRICANT, or similar maintenance spray (allowing it thirty seconds or so to penetrate) before introducing an Allen key-your frame threads will thank you.

 While rooting around in the spares boxes, I uncovered a set of solid axle mounts for the trailer. I’d acquired some along with the sprung hitch spares some years back. At that time, I’d been toying with Alfine and similar interplanetary (hub) transmissions. This never came to fruition. On a few occasions, I’ve tethered trailer and V2 fixed, primarily as part of wider product testing. Otherwise, gearing in the mid to high 70s isn’t synonymous with trailer tugging. However, 63inches might prove a better fit, should need arise.  

Using the Specialized Crossroads EX as a "control", I've done 250 miles with the Nutrak and found them grippy and relatively responsive, especially coming from 2.2-2.3-inch cross country rubber. Average speed across metalled road is 17mph against 14.5 with the Continental and CST Patrol in comparable conditions.  Even inflated to their maximum (65psi) they've felt supple and compliant without any trace of skittishness.

I'm experimenting with pressures and am forming the opinion that 50-55psi is the sweet spot for my tastes, but time, mileage and testing may say different. I'll be interested to see how they cope in gloopy mud, which may be a while off yet, given the long, hot and distinctly dry summer. My supposition is their narrower profiles, and tread pattern will crave through without clogging or causing mischief around the chainstays. 

From a personal perspective, I was delighted to find a 26x1.9 gravel tyre, alongside 700c and 650b, although I was curious as to whether Nutrak were seeking to tap into the quiet trend for mountain bike to gravel conversions. Something I raised with Madison when discussing the specifications.

 Now, they are intended as a tubeless setup, which is another nice touch for those running a conversion. They also proved a very tight fit, which is very welcome on a tubeless system, but calls for a decent tyre lever. This was particularly so when running them with a butyl tube- even aboard a very conventional cross-country rim. I was relieved to find my trusty Cyclo Advanced Tyre Removal and Fitting Tool worked its magic, saving considerable time, effort, blisters and agricultural language.  I am very particular about lending tools and there are some I will flat out refuse to let out of my sight. Said tyre wand falls firmly into this category, along with a Czech made headset press.